With the general seepage resulting from pressure from the saturated dirt outside the basement, trenches can be built to divert the water to the basement’s sump pump. With the other two locations—corners and staircase attachments—direct action may be taken on those two areas to curb the flood potential and attempt to waterproof the basement for good!

Here are some tips to work with when learning how to waterproof your basement:

• Identify the source(s) of water entering the basement. If the water appears to be coming in through one spot, attempt to identify that spot and reinforce it.

• Prepare to dig a trench in order to divert any water to the sump, the drainage hole in the basement floor. Be certain that the drainage grate is clear and able to let the water drain freely.

• Develop means to pump water into that drainage hole, the “sump pump.” Be extra careful when dealing with water and electricity; they make a dangerous combination when mixed! Avoid using extension cords to power your sump pump. Be sure to use grounded sockets. Industry has now even come up with a solar powered sump pump; that may be a safer, less deadly option.

• Locate ways to reinforce breaches in your basement’s wall integrity. Watch carefully for leaks around corner joists, staircase attachments, and crawl space entrances. See if your local building supply is familiar with products that other persons in your locale have used with success!

Begin to dig a trench in the spot where you want the water to begin to flow. This trench that will direct the water away should have a resulting grade of 1%, with the beginning of the trench being 1% higher than the end of it. That difference in grade will allow for a gentle slope which, when filled with rocks, will enable the water to run off through the rocks and away from where it could do damage to your lot.

Here are some tips for installing a French drains:

• Choose a location to divert the water to where it will not create any damage. That may be difficult; you may simply have to choose a location or you may need to install a Dry Well.

• Before beginning to dig your trench, check with the local utility authorities to be sure that you will not be digging near any of their pipes or easements.

• Plant a clean stick at the beginning of your trench and a second at the proposed end of the trench. Tie a string which is the length of the proposed trench firmly to the first stick at its ground level, wrapping the other end around the second. Use a string level to be sure that the string remains level. Firmly tie the second end to the second stick; these lengths will be compared to view the progress of your digging. You ultimately want your trench to be 100 feet long with the shallower end being six inches higher than the deep end.

• Fill the trench with rocks to provide a guide for the water as it runs off through the drain.

• Some experts on French drains advocate a narrow drain; others advise a wider drain with a width of 8-10 inches for water conduction purposes.

• Be sure that the new drain does not cause problem for any of your neighbors with lower-lying lots near yours!

Here are some handy tips for you to use when you install a sump pump to rid your house of unnecessary water:

• Be sure you hook up a pump which can thoroughly remove and properly divert the water by lifting it both up and away from the sump hole.  The capacity of the pump to be able to do that is called its “lift.”

• You want a pump that is strong enough to remove the water and direct it as far away from the house as possible.

• You must be absolutely certain that the connection of the pump and its electrical source are fully grounded, as electricity and water do not mix well or safely. The plug should ideally be a GFCI ground for your safety and the safety of the structure itself!

1.) You will need to get the carpet up off of the floor and then get it taken outside where it can begin to air out.  This is very important because you want to get the padding underneath of it out so you can replace it.  You do not want any mold growing under there.

2.) Clean the carpet with fresh, clear water so that it any dirt and residue will be removed.

3.) Use a good cleaner to clean the hard wood floor and run fans over the hard wood floor so that it will dry more quickly. You may need to replace any molding tongue and groove boards.

4.) Let the carpet air out for several days in order to ensure that it is completely dry.  You will only be defeating the purpose if you put it back while it is still wet.

5.) Place new padding on the floor and then tack the carpet back into place.

It is possible to save your carpet after you have experienced water damage.  However, you need to remember that it will be labor intensive and it will be time consuming.  If you do not have the time to do this work, or you just do not want to,  you might want to call a professional.

If you can see water flowing out of a crack in a wall or floor, you know that the source is ground water. If water is not flowing out of a crack, you’ll have to make a test for dampness in your basement to see if the water is due to condensation or water from the ground. To do this:

1. Cut two 12in squares of plastic sheeting or aluminum foil.
2. Tape a peace to the inside of one of the basement walls and the other to the basement floor.
3. Wait 2 days.
4. Remove the plastic or aluminum foil.
5. If the wall or floor that was covered by the square is dry then you have condensation. If the wall or floor that was covered by the squares are wet, you have a ground water leak.

Controlling Condensation In The Basement:

You will need to lower your basements air humidity by:

1. Raise the temperature in the basement.
2. Make sure all vents of moist air, like your clothes dryer, are vented to the outside.
3. Place a dehumidifier in the basement.
4. Insulate basement walls.
5. Insulate cold water pipes.
6. Open basement windows, weather permitting.

Controlling Ground Water Leaks In The Basement:

1. Gutters and downspouts should be directed to clear water away from the foundation of the home.
2. If you have a leaking crack, you will need to call a professional to fix the basement foundation.

Sleeve Clamp:

Adjustable Hose Clamp: Place an adjustable hose clamp over a rubber blanket over a small pipe leak and tighten the clamp.

C-Clap: Lock a C-clamp and a small block of wood on a rubber blanket for a small leak.

Epoxy Putty: Submit an application of epoxy putty to a leaking pipe joint (after turning off the water) using a putty knife or your fingers. Let the joint dry before turning back on the water.

Quick Fix-Up

Stopping A Small Leak: You can temporarily plug a small pipe leak with breaking off a pencil point in the leak hole. Then wrap the pipe with at least three layers of electrical tape, extending the tape 3 inches on each side of the leak.

Downspout Extenders: An extender are attach directly to the downspout. Extenders are made from aluminum, galvanized steel, or vinyl. They are constructed to carry the water away from the house, often into a drain. You can purchase a downspout extender at any home improvement center.

Splashblocks: An alternative to downspout extenders, splashblocks are placed below the elbow of the downspout. Splashblocks are ready-made with concrete or plastic. Ideally, the splashblock should extend at least 4 feet and should be slightly sloped so that the water runs well ahead of the house foundation. 

Dry Wells: If you live in a wet climate, you may want to connect your downspouts to a dry well. Locate the dry well 10 or more feet from your home. The well itself can be merely a hole 2 to 4 feet wide and 3 feet deep. Or you can bury a 55-gallon drum after piercing it with holes and removing both ends. Fill the well with rocks or broken concrete, and then cover the top with a wood plank or heavy roofing paper. The well’s top should be at least 18 inches under ground with the bottom above the water table.
The underground drainage pipes should slope ¼ to ½ inch per foot. This allows the water flow from the house downspout to the dry well.